Backyard Discovery 40112 Manuel d'utilisateur

Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-85



(Tape Measure)(Claw Hammer)(Cordless Drill or Electric Drill)(An Adult w/ an Adult Helper)(Rubber Mallet - Optional)(Ladder)(Phillips Screw Driver)(Dr

IIIImmmmppppoooorrrrttttaaaannnntttt AAAAsssssssseeeemmmmbbbbllllyyyy NNNNooootttteeeessss1) While assembling unit, take time before and after e

Parts IdentificationWood Components(NOT TO SCALE)E1 - FORT UPRIGHT - W1022971 3/8"x3 3/8"x83" (36x86x2108)(4)E77 - ANGLE BRACE - W10099

Parts IdentificationWood Components(NOT TO SCALE)K3 - WALL RAIL - W1023025/8"x5 1/4"x30" (16x134x762)(3)K4 - ARCHED WALL RAIL - W102306

Parts IdentificationWood Components(NOT TO SCALE)M11 - ROCKWALL BOARD - W1023365/8"x3 3/8"x20 1/4" (16x86x514)(6)M12 - WALL RAIL - W102

Parts IdentificationHardware BOLT WH 5/16x1/2 - H100115(6) BOLT WH 5/16x1 - H100008(2) BOLT WH 5/16x1-1/2 - H100010(23) BOLT WH 5/16x1-3/4 - H100011(6

Parts IdentificationHardware SCREW PFH 8x1-1/8" - H100088(92) SCREW PFH 8x1-1/2" - H100086(57) SCREW PFH 8x2 - H100111(7) SCREW PFH 8x2-1/4

Parts IdentificationAAAAcccccccceeeessssssssoooorrrriiiieeeessss(NOT TO SCALE)GZ - SLIDE RAIL 8' BLUE RIGHT-A100161(1)HA - SLIDE RAIL 8' BLU

Parts IdentificationAAAAcccccccceeeessssssssoooorrrriiiieeeessss(NOT TO SCALE)EA - HAND GRIP YELLOW PLASTIC-A100043(2)GX - CLIMBING ROCK BLUE SMALL-A

PLEASE HAVE THE FOLLOWING INFORMATION WHEN YOU MAKE YOUR CALL: 1 – MODEL NUMBER OF THE PRODUCT LOCATED ON THE FRONT OF THE ASSEMBLY MANUAL 2 – DESRIP

3 5/88 5/813 5/81NUT BARREL WH 5/16x5/8WASHER LOCK EXT 12x19SLIDE BRACEBOLT WH 5/16x1/2SLIDE BED 8' YELLOW8 FOOT SLIDE ASSEMBLYPHASE 1STEP 1 ● DR

SLIDE RAIL 8' BLUE LEFTSLIDE RAIL 8' BLUE RIGHTCENTER SLIDE BRACESTEP 2 PLACE 1 SLIDE RAIL ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED A

STEP 1 ATTACH (2) SB TRIANGLE PLATES TO SB74 SWING BEAM USING 1-3/4" BOLTS, LOCK WASHER AND 7/8" BARREL NUT. ATTACH (2) GQ L BRACKETS TO SB7

STEP 2 INSERT (2) 2-1/2" BOLTS, LOCK WASHERS AND 1-1/2" BARREL NUTS INTO TOP EDGE OF W71 SWING BEAM SUPPORT, AS SHOWN. ATTACH E77 ANGLE BRAC

SWING BEAM ASSEMBLYSB74W71 WASHERSAFETY17x30 (4) WASHERFLAT 8x27 (4) NUT LOCK5/16 (4) SWINGHANGERQUICK LINK (4) NUT BARRELWH 5/16x7/8 (2) WASHERLOCK E

STEP 1 LAY TWO E1 FORT UPRIGHTS FLAT ON GROUND. ATTACH K1 BOARD TO E1 FORT UPRIGHTS USING 1- 1/2" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS.S

STEP 5 ATTACH H4 FLOOR JOIST TO E1 FORT UPRIGHTS USING 2" BOLTS, LOCK WASHERS AND 7/8" BARREL NUTS. ATTACH M6 FLOOR SUPPORT TO E1 FORT UPRIG

STEP 7 STAND UP UPRIGHT ASSEMBLIES AND ATTACH (2) K2 GROUND BOARDS TO E1 FORT UPRIGHTS USING 2" LAG SCREWS AND LOCK WASHERS.STEP 9 ATTACH K4 ARCH

STEP 11 ATTACH (2) K5 OUTER FLOOR BOARDS TO H4 FLOOR JOISTSAND M5 FLOOR SUPPORTS USING 1-1/2" WOOD SCREWS.STEP 10 ATTACH H6 FLOOR SUPPORT TO M5

STEP 12 EVENLY SPACE (6) M4 FLOOR BOARDS AND ATTACH TO H4 FLOOR JOISTS USING 1-1/2" SCREWS. ATTACH H6 FLOOR SUPPORT TO M4 FLOOR BOARDS USING 1-

Owner’s Manual Play Set

STEP 14 TO BUILD THE ROCK WALL LADDER ASSEMBLY, START BY ATTACHING THE GX CLIMBING ROCKS TO M11 WALL BOARDS USING 1-1/2" BOLTS, 3/8" T-NUTS

STEP 16 ATTACH (3) M9 WALL SLATS TO K3 WALL RAIL AND M6 FLOOR SUPPORT USING 1-1/8" WOOD SCREWS.M9M6K31 13/16"3 1/4"(3 PLCS)STEP 17 ATTA

STEP 18 ATTACH (2) N1 WALL SLATS TO K4 ARCHED WALL RAIL AND M12 WALL RAIL USING 1-1/8" WOOD SCREWS.STEP 19 ATTACH H3 TARP UPRIGHT TO H1 ROOF CROS

STEP 20 DRAPE SC TARP OVER M2 AND M8 TARP SUPPORTS. ATTACH ONE SIDE OF TARP TO INSIDE OF ONE M2 TARP SUPPORT USING 5/8" SCREWS. PULL OTHER SIDE O

STEP 21 PILOT DRILL USING 1/8" BIT AND ATTACH (2) G1 PICNIC TOP SUPPORTS TO E1 FORT UPRIGHTS USING 3" WOOD SCREWS. SEE PILOT DRILL HOLE LOCA

STEP 23 ATTACH PICNIC TABLE TOP ASSEMBLY TO G1 PICNIC TOP SUPPORTS USING 1-1/2" WOOD SCREWS. SCREW PFH 8x1-1/2" (4)TABLE TOP ASSEMBLYG1N3M3

STEP 25 ATTACH SEAT SUPPORT ASSEMBLY TO K2 GROUND BOARDS USING 1-1/8" WOOD SCREWS. SCREW PFH 8x1-1/2" (4) SCREW PFH 8x1-1/8" (8)STEP 24

SCREW PFH 8x1-1/2" (4)STEP 26 ATTACH TABLE TOP & SEAT ASSEMBLY TO (2) J1 TIE STRAPS USING 1-1/2" WOODSCREWS.TABLE TOP & SEAT ASSEMB

STEP 27 ATTACH EA HANDLE GRIPS TO N1 WALL SLATS USING 1/4"x 1" BOLTS, 6x15 LOCK WASHERS AND 1/4" T-NUTS. USING A 5/16" DRILL BIT P

STEP 28 BEGIN BY PILOT DRILLING H1 ROOF CROSS BRACE WITH 3/8" BIT USING SWING BEAM ASSEMBLY ANGLE BRACKETS AS A TEMPLATE.ATTACH SWING BEAM A

Owner’s Manual Play Set

STEP 29 CENTER SLIDE ASSEMBLY IN OPENING, AS SHOWN. USING HOLE PATTERN BELOW, PILOT DRILL (3) SLIDE ATTACHMENT HOLES IN SLIDE BED AND K5 OUTER FLOOR

Anchoring InstructionsNOTE:FAILURE TO USE STAKES CAN VOID WARRANTY & CAUSE INJURY!*STAKES SHOULD BE PLACED IN CONCRETE*FINAL STEP DOUBLE CHECK EVE

Rev5/20/10 BRS Limi

Owner’s Manual Play Set

Owner’s Manual Play Set

Owner’s Manual Play Set

Owner’s Manual Play Set

